Horse Fencing Fundamentals: Posts & Braces
By John Ferris, Full Dip. Tech., Prod. Eng.
The humble fence post is the foundation of our fencing project, and one of the most important commodities in our equine and farming society. It is the mainstay required to produce and maintain healthy pastures, protect our livestock and food sources from predators, determine our boundaries, and add value to our real estate.
Because fence posts are so important, we must chose the right posts for the job, and install them correctly. A good rule of thumb is to never go too small for the job at hand, always go larger. The slight increase in cost will save money in the long run, and the end result will be far more pleasing to the eye. We must stop taking the fence post for granted and thinking of it as a frivolous item, and installing it with the same attitude.
When considering your fence posts, weigh your options by asking yourself some basic questions: What will the post be used for? Is it going to be a permanent fixture, or will it be stored away in the barn when the grazing/growing season is over? What type of post can be installed in the ground you are dealing with? What are your maintenance expectations? As a rule of thumb, always use posts which are at least one foot longer for corners, gates, brace posts, and end posts.
I often come across the old problem of posts not deep enough into the ground and not large enough in diameter to do the job they are expected to do. If you are planning an arena, round pen, loafing paddocks, or any area into which you are going to add footing, do not consider the depth of the additional footing to be a part of the depth into which the posts have to be pounded. For example, if you are going to add six inches of footing, allow for a longer post to give the height above the ground, because the post has to go two and a half feet or more into the original ground for line posts, and three and a half feet or more into the original ground for the corners, ends, and gateways.
Bracing is an important element of fencing to ensure fence stability and security. Make sure you brace correctly to avoid leveraging the post out of the ground rather than in. Photo: Pam MacKenzie Photography
If you are getting an installer or neighbour to do your post pounding, do not be satisfied with anything less than the depths I have recommended, even though you may meet with protest from the person operating the machine.
In some situations the posts will not go into the ground due to rock or severe hardpans. In these cases it is recommended that you rent a pneumatic drill and chip away the substance, keeping the hole as close to the diameter of the post as possible in order that the post maybe locked into the ground.
Do not use small diameter posts in these cases as you are increasing the possibility of having the post snap off at the ground level.
Sometimes, one just has to use a metal post to compensate for the difficulty in installing a wooden post. If this is the case, I recommend a three and a half inch diameter schedule 40 tube. Avoid using the light duty mild steel as this will surely flex. Of course, if the situation allows, it is probably easier to plan the fence away from such difficult areas.
The importance of large and sturdy posts for the corners, ends, and gateways cannot be overstressed. This also includes the brace post, which is the next or second post in the brace configuration. Braces are an essential part of fence construction and the physics of such brace assemblies have to be correct to do the job. Otherwise, you may end up levering the post out of the ground instead of keeping it in. I cannot emphasize enough the importance of correct bracing.
Diagrams are the best way to explain brace construction so I have set out a few standard BC Ministry of Agriculture engineered braces below with notes to go with them. These diagrams illustrate bracing needed for tensioned wire, polymer, diamond mesh, no climb, farm, and other tensioned products.
Typical Brace Assemblies & Their Uses
Single Brace Assembly: This is used at the beginning and the end of a straight run, on either side of a gateway, mid-fence line (about every 300 feet) on a long run where an in-line brace is required to add stability to the fence, and where there is undulation in the land or a slight change of direction.
Double Brace Assembly: Used where a single brace assembly is considered insufficient due to length of runs, ground conditions, etc.
Corner Brace Assembly: Used at right angled corners.
Round Corner Brace Assembly: Used where a right angled corner is not desired, i.e. slightly rounded corner.
Detailed Single Brace Assembly
The diagram below shows the materials required to construct a brace. You will notice that I have raised the point of the diagonal wire at the base of the corner post up from the ground approximately 16 to 18 inches. Not only is the injury risk reduced, but from an engineering point of view, the brace is more stable. You will also notice that I have designed a brace in which the diagonal wire can be reduced to a single strand, eliminating the loop at the base of the corner post and top of the next post. The wire is covered by Insul-Tube®, again to lessen the injury risk. This is tensioned with a wire vise tensioning device. This is also very attractive with the white tubing.
DETAILED SINGLE BRACE ASSEMBLY
This diagram shows a ten foot horizontal brace rail; one can go seven feet, eight feet, nine feet, to a maximum of ten feet on a brace span. This horizontal rail should be a solid rail. I am very much against sawn lumber, (e.g. 2”x4”, 2”x6”, etc.) or landscape ties being used for this job. Round is much stronger than square and can absorb the forces of the tensioning far better. Squared or sawn lumber weakens, bows, and often ends up splintering, sometimes into deadly spears. The diagonal wire can be substituted by a rail (not squared lumber) if one does not want to use wire, but wire does a better job of holding those bracing posts in place.
On the subject of wire, make sure those brace wires are high tensile galvanized steel. Low tensile or soft wire is easier to work with but does not do the job adequately — it will slacken and belly over time and often the galvanizing is poorer and rust sets in.
You will notice from the detailed material used in the brace assembly that I use rebar or a large pin to attach the horizontal rail to the brace posts. Pre-drill a three-eighths inch hole in the centre of either end of the rail and into the brace post in order to accommodate the rebar or pin to avoid splitting the wood. Do not toenail (hammer a large nail at an angle through the horizontal rail into the post). These are dangerous areas and the chances of splitting and weakening the wood are very high.
There are various other types of brace configurations for different situations, but the ones I have shown are the most widely used and are suitable for almost all conditions.
Related: Safe and Functional Horse Fencing
There are several options for bracing a fence. This one has been tensioned by twisting the two wires together. You may prefer to use the Insul-Tube® method or a solid post instead. Photo: Pam MacKenzie Photography
Directions for High Tensile Steel Wire Not Covered by Insul-Tube®
Start at the bottom of the post, wrap the wire, and attach it securely to the post with staples approximately 16 to 18 inches off the ground, making sure to leave no sharp edges protruding that may injure animal or human. Take the wire up to the top of the other brace post and secure it with a staple, leaving enough room so that the wire can run freely through the staple. Now take the wire back to the bottom of post where you started, approximately 16 to 17 inches off ground; pull as tight as possible and cut the wire, leaving enough securely attached to the post. Again, make sure there are no sharp edges.
At the bottom of the post (letter A on the diagram), insert a large screwdriver or bar, low to the ground, and twist the two wires together to the desired tension. Remove the screwdriver or bar and cover the wire with plastic pipe or tubing for additional safety, if desired. Twitch sticks can be chewed by horses and halters can catch in them, so use at your own risk. If you have long spans of fence line go to double brace assemblies.
Directions for Single Diagonal High Tensile Steel Wire Brace Covered with Insul-Tube®
Wrap the end of the high tensile steel wire at the corner or end post about 16 to 18 inches above the ground, and secure it with a staple. Then drill a hole for a wire vice (size 5058) about six inches below the top of the post. Cut the wire to length, cover it with Insul tube, and pass the wire through the drilled hole into a wire vice. Push the wire vice into the hole and tension up. No twisting with a screwdriver or bar is required when using this method.
Now that the posts are well into the ground and the braces are correctly assembled, your fence is ready for fabrication.
Related: Horse Fencing for Special Needs
Author John Ferris and his wife Lesley have operated Ferris Fencing for more than 20 years, specializing in equine, general farm, horticulture, and vineyard applications, complete electric systems, and electric nets. As farmers, horse owners, and engineers, they are experts in the technical aspects of installation and application of fencing systems. For more information, visit www.ferrisfencing.com.
Main photo: The right fence posts, correctly installed, will require less maintenance, increase your property value, and protect your horses and other livestock from harm. ChristinaHandleyStock.com
This article originally appeared in the May/June 2010 issue of Canadian Horse Journal.